Rechercher des projets européens

11 projets européens trouvés

Recherche sur 125080 projets européens

 TERMINÉ 

Mechanical control of biological function (MECHANO-CONTROL)

Date du début: 1 janv. 2017, Date de fin: 31 déc. 2021,

Mechanical forces transmitted through specific molecular bonds drive biological function, and their understanding and control hold an uncharted potential in oncology, regenerative medicine and biomaterial design. However, this potential has not been realised, because it requires developing and integrating disparate technologies to measure and manipulate mechanical and adhesive properties from the ...
Voir le projet

 7

 TERMINÉ 

A multiscale approach towards mesostructured porous material design (MULTIMAT)

Date du début: 1 mars 2016, Date de fin: 29 févr. 2020,

"MULTIMAT addresses (1) the industrial and societal need for affordable materials that have a highly defined and large porosity together with the required (mechanical, chemical and/or thermal) robustness for application in thermal insulation, catalysts, fuel cells and oil spill remediation and (2) the scientific need to better understand the mechanisms underlying the assembly of small building blo ...
Voir le projet

 8

 TERMINÉ 

Training in Bio-Inspired Design of Smart Adhesive Materials (BioSmartTrainee)

Date du début: 1 oct. 2015, Date de fin: 30 sept. 2019,

The last half century has seen a tremendous advancement in adhesives technology and has led to widespread replacement of mechanical fasteners with adhesive bonds (e.g. aircraft, automobile, construction, etc.). Bonding to wet, rough and fouled surfaces, however, remains challenging and adhesive technology is rarely applied for bonding in wet conditions, such as in (orthopaedic) medicine. Therefore ...
Voir le projet

 11

 TERMINÉ 

Engineering of biomimetic surfaces: Switchable micropatterns for controlled adhesion and touch (SWITCH2STICK)

Date du début: 1 févr. 2014, Date de fin: 31 janv. 2019,

"Nature has, in the course of evolution, found many fascinating solutions to “engineering problems”. The proposed work aims at three-dimensional (3D) surface structures inspired by insects, spiders and geckoes. Based on the PI’s earlier work on passive structures, the new challenge addressed by this interdisciplinary project is to design and investigate active, switchable 3D micropatterns, whose a ...
Voir le projet

 1

 TERMINÉ 

Development and implementation of Grouping and Safe-by-Design approaches within regulatory frameworks (NanoREG II)

Date du début: 1 sept. 2015, Date de fin: 31 août 2018,

One of the greatest challenges facing regulators in the ever changing landscape of novel nano-materials is how to design and implement a regulatory process which is robust enough to deal with a rapidly diversifying system of manufactured nanomaterials (MNM) over time. Not only does the complexity of the MNM present a problem for regulators, the validity of data decreases with time, so that the wel ...
Voir le projet

 46

 TERMINÉ 

Indium-Free Transparent Conductive Oxides for Glass and Plastic Substrates (INFINITY)

Date du début: 1 déc. 2014, Date de fin: 31 janv. 2018,

INFINITY will develop an inorganic alternative to a scarce and high cost material, indium tin oxide (ITO), currently used as a Transparent Conductive Coating (TCC) for display electrodes on glass and plastic substrates. The novel conductive materials to be developed in this project will be based on low cost sol-gel chemistry using more widely available metallic elements and will leverage recent ad ...
Voir le projet

 9

 TERMINÉ 

Self-repairable Zinc-free Weldable Anti-corrosion Primer for the Steel protection (WELDAPRIME)

Date du début: 1 févr. 2014, Date de fin: 31 janv. 2017,

The global production of steel is in the range of 1400M tons, worth nearly €1trillion. The steel demand in Europe in 2011 was estimated to be 145M tons, of which 39M tons p.a. for the construction sector and 16M tons p.a. for structural steel. Most of this steel is carbon or mild steel (as opposed to stainless steel) which corrodes at a high rate and although there are a significant number of anti ...
Voir le projet

 10

 TERMINÉ 

Processing and Characterization of Advanced Nano-Composites for Resource-efficient Applications and Technologies (CREATe-Network)

Date de fin: 1 janv. 2015,

CREATe-Net is composed of 3 academic institutions in Europe (Saarland Univ., DE; Technical Univ. of Catalonia, ES; and INM - Leibniz Institute for New Materials, DE), 3 non-academic institutions in Europe (AB Sandvik Coromant, SE; Steinbeis Research and Innovation Centers, DE; and Nanoforce Ltd., UK), as well as 6 academic partners outside Europe (CSIR - Council for Scientific and Industrial Resea ...
Voir le projet

 6

 TERMINÉ 

In-line characterisation of nanoparticles using a combination of analytical techniques in real time (In-Sight)

Date du début: 1 mai 2011, Date de fin: 30 avr. 2014,

In-Sight is a SME-driven project on the in-line characterisation of nanoparticles during nanomaterial manufacturing. This in-line characterisation is the ultimate goal. Within the time-span of the project (3 years) it is our objective to show that a combination of analytical techniques that are capable of real time measurements will provide valuable information for the nanoparticle user. It is our ...
Voir le projet

 10

 TERMINÉ 

Nano-structured copper coatings, based on Vitolane technology, for antimicrobial applications (CuVITO)

Date du début: 1 oct. 2010, Date de fin: 31 déc. 2013,

Antibacterial coatings represent a huge market in healthcare and food sectors.CuVito brings together Mexican mining products and European product development, to produce a state-of-the-art copper nano-structured coating. Bacteria in hospitals present a major health issue.The effectiveness of cleaning is considerably enhanced on smooth, scratch-free surfaces.Anti-bacterial silver coatings are avail ...
Voir le projet

 8

 TERMINÉ 

Printable memory solutions for sensor, ID, and media applications (PriMeBits)

Date du début: 1 janv. 2008, Date de fin: 31 déc. 2010,

In the PriMeBits project, a printable electric low-voltage non-volatile memory is developed for printed sensor, media and wireless ID applications. The main strategy is to utilize printed technology where it has a competitive advantage compared to silicon technology. The project builds on basic research of new materials and components and takes the results into prototyping of new applications. To ...
Voir le projet

 11