Rechercher des projets européens

29 projets européens trouvés

Recherche sur 125080 projets européens

 TERMINÉ 

Soot Processes and Radiation in Aeronautical inNOvative combustors (SOPRANO)

Date du début: 1 sept. 2016, Date de fin: 31 août 2020,

For decades, most of the aviation research activities have been focused on the reduction of noise and NOx and CO2 emissions. However, emissions from aircraft gas turbine engines of non-volatile PM, consisting primarily of soot particles, are of international concern today. Despite the lack of knowledge toward soot formation processes and characterization in terms of mass and size, engine manufactu ...
Voir le projet

 18

 TERMINÉ 

Innovative controls for renewable sources Integration into smart energy systems (INCITE)

Date du début: 1 déc. 2015, Date de fin: 30 nov. 2019,

The continuous increase of the share of renewable energy sources is redefining the electrical networks. In future infrastructures, an important number of agents (sources, storage devices and consumers) will have intelligent interfaces allowing the regulation of the injection and extraction of power into the grid. This context will create multiple alternatives to increase the efficiency in electric ...
Voir le projet

 9

 TERMINÉ 

Closed Loop Wind Farm Control (CL-Windcon)

Date du début: 1 nov. 2016, Date de fin: 31 oct. 2019,

Current practice in wind turbines operation is that every turbine has its own controller that optimizes its own performance in terms of energy capture and loading. This way of operating wind farms means that each wind turbine operates based only on the available information on its own measurements. This gets the wind farm to operate in a non-optimum way, since wind turbines are not operating as pl ...
Voir le projet

 15

 TERMINÉ 

Navigating the Roadmap for Clean, Secure and Efficient Energy Innovation (SET-Nav)

Date du début: 1 avr. 2016, Date de fin: 31 mars 2019,

SET-Nav will support strategic decision making in Europe’s energy sector, enhancing innovation towards a clean, secure and efficient energy system. Our research will enable the EC, national governments and regulators to facilitate the development of optimal technology portfolios by market actors. We will comprehensively address critical uncertainties and derive appropriate policy and market respon ...
Voir le projet

 16

 TERMINÉ 

Turning waste from steel industry into a valuable low cost feedstock for energy intensive industry (RESLAG)

Date du début: 1 sept. 2015, Date de fin: 28 févr. 2019,

The RESLAG project proposal is aligned with the challenges outlined in the call WASTE-1-2014: Moving towards a circular economy through industrial symbiosis. In 2010, the European steel industry generated, as waste, about 21.8 Mt of steel slag. The 76 % of the slag was recycled in applications such as aggregates for construction or road materials, but these sectors were unable to absorb the total ...
Voir le projet

 22

 TERMINÉ 

Flexible Fossil Power Plants for the Future Energy Market through new and advanced Turbine Technologies (FLEXTURBINE)

Date du début: 1 janv. 2016, Date de fin: 31 déc. 2018,

The share of renewable energy is growing rapidly driven by the objective to reduce greenhouse gas emissions. The amount of electric power which can be supplied to the grid depends on the time of the day and weather conditions. A conventional fleet of thermal power plants is required to compensate for these fluctuations before large scale energy storage technologies will be mature and economically ...
Voir le projet

 23

 TERMINÉ 

Unifying Control and Verification of Cyber-Physical Systems (UnCoVerCPS)

Date du début: 1 janv. 2015, Date de fin: 31 déc. 2018,

The proposed research effort provides methods for a faster and more efficient development process of safety- or operation-critical cyber-physical systems in (partially) unknown environments. Cyber-physical systems are very hard to control and verify because of the mix of discrete dynamics (originating from computing elements) and continuous dynamics (originating from physical elements). We present ...
Voir le projet

 11

 TERMINÉ 

Personalised Prognostic Tools for Early Psychosis Management (PRONIA)

Date du début: 1 oct. 2013, Date de fin: 30 sept. 2018,

...sychoses. Thus, we will first use routine brain imaging and complementary data to optimise our candidate biomarkers for the prediction and staging of psychoses and generate a prognostic system that generalises well across mental health services. Secondly, we will implement new multi-modal risk quantification tools to predict mental health-related disability in young help-seekers. The fusion of the ...
Voir le projet

 13

 TERMINÉ 

AUTomotive deRivative Energy system (AutoRE)

Date du début: 1 août 2015, Date de fin: 31 juil. 2018,

"The overall aim is to create the foundations for commercializing an automotive derivative fuel cell system in the 50 to 100 kW range, for combined heat and power (CHP) applications in commercial and industrial buildings. More specifically, the project has the following objectives:• develop system components allowing reduced costs, increased durability and efficiency • build and validate a first ...
Voir le projet

 7

 TERMINÉ 

Predictable Flexible Molten Salts Solar Power Plant (PreFlexMS)

Date du début: 1 juin 2015, Date de fin: 31 mai 2018,

Predictability and flexibility are key enablers to increase CSP penetration in the energy mix by a) increasing dispatchability b) making CSP less/not reliant on subsidies c) supporting stable grid operation d) enabling operators to access new revenue streams (electricity trading, ancillary services). Today CSP plants with molten salt storage only partly achieve these objectives. Key enabling techn ...
Voir le projet

 16

 TERMINÉ 

Real-time dynamic control system for laser welding (RADICLE)

Date du début: 1 févr. 2015, Date de fin: 31 janv. 2018,

RADICLE aims to create a real-time dynamic control system for laser welding using a combination of (application specific) sensors in combination with intelligent and predictive control technologies for in-process monitoring and control to minimize/eliminate defects for a range of materials and geometries for both aerospace, automotive and other applications. The control system will include pre- an ...
Voir le projet

 12

 TERMINÉ 

AdVanced Aerodynamic Tools for lArge Rotors (AVATAR)

Date du début: 1 nov. 2013, Date de fin: 31 oct. 2017,

The motivation for the AVATAR project lies in the fact that upscaling wind turbine designs towards 10-20 MW requires radical innovations to make this feasible. Many of these innovationshave a strong aerodynamic component and can be considered as unconventional from an aerodynamic point of view. As such the analysis of the resulting rotor designs falls outside the validated range of applicability o ...
Voir le projet

 14

 TERMINÉ 

Hub of Application Laboratories for Equipment Assessment in Laser Based Manufacturing (APPOLO)

Date du début: 1 sept. 2013, Date de fin: 31 août 2017,

During more than 50 years of the laser existence, they have been proved as the unique tool for diverse material processing application. New application ideas, coming from universities and research institutions, are usually implemented by spin-off companies with limited resources for market penetration. Research laboratories are using universal laser tools, while effective and low-cost production r ...
Voir le projet

 36

 TERMINÉ 

Innovative Practices in Renewable Energies to Improve Rural Employability

Date du début: 1 sept. 2014, Date de fin: 30 août 2017,

...hus, it is seen as a part of a long-term collaboration that started with the ongoing Erasmus Intensive Programme “IT-Forest” and will provide the incomes for new joint initiatives. OBJECTIVES The general objective of IN2RURAL is to promote innovative practices in the renewable energies sector to improve the employability of university students in the rural areas of Bacau (Romania), Castellón (Spai ...
Voir le projet

 5

 TERMINÉ 

Self-Healing Thermal Barrier Coatings (SAMBA)

Date du début: 1 mars 2013, Date de fin: 28 févr. 2017,

"This project deals with the creation of a new, unique self-healing thermal barrier coating (TBC) for turbines and other thermally loaded structures in order to realize a significant extension of the lifetime of critical high-temperature components. The concept is based on novel Al2O3 coated Mo-Si particles embedded in the TBC layer, typically consisting of yttria-stabilised zirconia. As the curre ...
Voir le projet

 9

 TERMINÉ 

Oxide Dispersion Strengthened Materials for the Additive Manufacture of High Temperature Components in Power Generation (OXIGEN)

Date du début: 1 févr. 2013, Date de fin: 31 janv. 2017,

OXIGEN will combine leading-edge European expertise in the manufacture of specialist powder alloys (Mechanical Alloying), knowledge of niche high-temperature materials and capabilities in additive manufacturing. This will produce an integrated, world-leading capability to directly manufacture from powder to part custom-designed, best-in-class high temperature alloys for power generation component ...
Voir le projet

 11

 TERMINÉ 

Smart and Sustainable Insular Electricity Grids Under Large-Scale Renewable Integration (SINGULAR)

Date du début: 1 déc. 2012, Date de fin: 30 nov. 2015,

...imized. The operation and planning tools and procedures will be applied in different insular electricity grids in five countries across Europe for extensive demonstration, allowing the development of generalized guides of procedures and grid codes specific for future generation of smart insular electricity grids.
Voir le projet

 16

 TERMINÉ 

Dynamic manufacturing of thin-walled work pieces by milling process (DYNAMILL)

Date du début: 1 nov. 2012, Date de fin: 31 oct. 2015,

Lightweight components are gaining in importance in EU key industries with good market growth potential (aerospace, automotive, power generation, medical technology etc.). To achieve weight reductions, complex thin-walled structures are combined with high strength materials. However, the lower stiffness of work pieces leads to severe challenges during the milling process:- Difficulty to achieve hi ...
Voir le projet

 10

 TERMINÉ 

web-based enerGy management system foR the optimization of the EnErgy coNsumption in Hospitals (GREEN@Hospital)

Date du début: 1 mars 2012, Date de fin: 28 févr. 2015,

Hospitals are known to be large energy consumers and in most European countries the high proportion of ageing building stocks makes hospitals amongst the least energy efficient public buildings. Nowadays there is a growing urgency to achieve real energy savings from existing building stocks and to build more sustainable new hospitals.The GREEN@Hospital project aims at integrating the latest ICT so ...
Voir le projet

 11

 TERMINÉ 

Meeting the Materials and Manufacturing Challenge for Ultra High Efficiency PF Power Plants with CCS (NEXTGENPOWER)

Date du début: 1 mai 2010, Date de fin: 31 oct. 2014,

Carbon Capture and Sequestration has become an important technology to comply with the CO2 reduction targets set by the EC. However CCS has the drawback that the electrical efficiency of the coal fired power plant will drop significantly. To overcome this drawback, one has to increase the base efficiency of the power plant or increase the biomass co-firing share as this is a CO2 neutral energy sou ...
Voir le projet

 15

 TERMINÉ 

Multiscale computational approach to the design of polymer-matrix nanocomposites (COMPNANOCOMP)

Date du début: 1 oct. 2011, Date de fin: 30 sept. 2014,

"This project aims at the development of multiscale simulation methodology and software for predicting the morphology (spatial distribution and state of aggregation of nanoparticles), thermal (glass temperature), mechanical (viscoelastic storage and loss moduli, plasticity, fracture toughness and compression strength), electrical and optical properties of soft and hard polymer matrix nanocomposite ...
Voir le projet

 8

 TERMINÉ 

Using real-time measurements for monitoring and management of power transmission dynamics for the Smart Grid (REAL-SMART)

Date du début: 1 sept. 2010, Date de fin: 31 août 2014,

Power transmission in Europe is entering a period of significant renewal and technological change because the electrical transmission grids face increases in new and variable energy sources, especially from large scale wind power generators. They therefore face future challenges of operation and control. Changes happening in the process industries will also have an impact on electrical supply beca ...
Voir le projet

 11

 TERMINÉ 

Engine Representative Internal Cooling Knowledge and Applications (ERICKA)

Date du début: 1 juil. 2009, Date de fin: 30 juin 2014,

"The goal of ERICKA is to directly contribute to reductions in aircraft engine fuel consumption with a targeted contribution of 1% reduction in SFC relative to engines currently in service. The fuel efficiency of a jet engine used for aircraft propulsion is dependent on the performance of many key engine components. One of the most important is the turbine whose efficiency has a large influence ...
Voir le projet

 20

 TERMINÉ 

Open Rotor Engines Advanced Technologies II (OREAT II)

Date du début: 1 déc. 2011, Date de fin: 31 juil. 2013,

"A principal contributor to affordable and sustainable public air transportation will be the introduction of more fuel-efficient propulsion systems, one of which is the Open Rotor Engine concept. Unlike turbofans, open rotors must vary blade pitch to accommodate power and aircraft speed range, so a key element to the viability of the concept is the actuation and control of the blade pitch via the ...
Voir le projet

 3

 TERMINÉ 

Development of High Temperature Survival Electronic Devices for Engine Control Systems (HIGHTECS)

Date du début: 1 janv. 2010, Date de fin: 31 juil. 2013,

"This proposal is concerned with the development of distributed high temperature electronics platform for integration with sensor elements to provide a high integrity serial digital data link that can be fed into FADEC (Full Authority Digital Electronic Control) and/or EHMS (Engine Health Monitoring System) units on an aircraft engine. To date most of the work undertaken and reported has been in t ...
Voir le projet

 3

 TERMINÉ 

Advanced NAno-Structured TApeS for electrotechnical high power Insulating Applications (ANASTASIA)

Date du début: 1 janv. 2010, Date de fin: 31 déc. 2012,

The objective is to develop radically innovative electrical insulating tapes and process to improve the energy conversion efficiency of electrotechnical systems. It mainly addresses the electric power generation issue. Today, the energy conversion efficiency of generators is restricted by (i) thermal as well as (ii) electrical strength limitations due to the electrical insulator tapes themselves. ...
Voir le projet

 10

 TERMINÉ 

Enabling advanced pre-combustion capture techniques and plants (DECARBIT)

Date du début: 1 janv. 2008, Date de fin: 30 juin 2012,

DECARBit responds to the urgent need for further research and development in advanced pre-combustion capture techniques to substantially reduce emissions of greenhouse gases from fossil fuel power plants. The project will accelerate the technology development and contribute to the deployment of large scale carbon capture and storage (CCS) plants in line with the adopted European policies for emiss ...
Voir le projet

 18

 TERMINÉ 

Open Rotor Engines Advanced Technologies for rotor blade pitch change mechanism (OREAT)

Date du début: 1 janv. 2010, Date de fin: 30 sept. 2011,

"Pitch Change Mechanism Conceptual and Preliminary Design Activities. A principal contributor to affordable and sustainable public air transportation will be the introduction of more fuel-efficient propulsion systems, one of which is the Open Rotor Engine concept. Unlike turbofans, open rotors must vary blade pitch to accommodate power and aircraft speed range, so a key element to the viability of ...
Voir le projet

 3

 TERMINÉ 

Converting Laminates into Energy and Aluminium for the benefit of Nature (CLEAN)

Date du début: 1 mai 2006, Date de fin: 30 avr. 2010,

Background In Europe, more than a million tonnes of drink cartons are thrown away after use every year. More and more of these drink cartons are now being recovered in various types of collection schemes (29% in 2004). The 300 000 tonnes recovered are processed in the paper industry, where the paper fibres (210 000 tons) are fully recycled into new paper ...
Voir le projet

 4