7 projets européens trouvés
Recherche sur 125080 projets européens
TERMINÉ
High resolution electron beam melting (HiResEBM)
Date du début: 1 oct. 2011, Date de fin: 30 sept. 2015,
HiResEBM is a partnership between EU SMEs and RTD providers with the aim of developing an electron beam melting (EBM) additive manufacturing process to enable the fabrication of high resolution medical implants with optimised porous structures directly from metal powder. Currently the design of medical implants with porous structures is limited by production technologies not being able to implemen ...
Voir le projet
6
Participants partenaires
TERMINÉ
INNOVATIVE SMART COMPOSITE MOULDS FOR COST-EFFECTIVE MANUFACTURING OF PLASTIC AND COMPOSITE COMPONENTS (COEUS-TITAN)
Date du début: 1 mars 2011, Date de fin: 28 févr. 2014,
Currently, composite moulds are mainly used in open-mould manufacturing processes and in Light RTM (a low-pressure variation of RTM). The proposed project aims to extend the applicability of composite moulds into the more demanding regime of RTM production, as well as to extend the application of the open mould and light RTM techniques in the field of advanced resin systems, where elevated tempera ...
Voir le projet
13
Participants partenaires
TERMINÉ
Demonstration of a Condition Monitoring System for Tidal Stream Generators (TidalSense Demo)
Date du début: 1 févr. 2012, Date de fin: 31 janv. 2014,
The TidalSense Demo project has been conceived by the SMEs intending to exploit a new market with huge potential growth, in Condition Monitoring of subsea energy device elements using the TidalSense System. The TidalSense condition monitoring system has been developed to detect, locate and classify defects in tidal generator structures. The Demo project will allow the SMEs to demonstrate and valid ...
Voir le projet
13
Participants partenaires
TERMINÉ
High Productivity Electron Beam Melting Additive Manufacturing Development for the Part Production Systems Market (FastEBM)
Date du début: 1 déc. 2011, Date de fin: 30 nov. 2013,
Electron beam melting additive manufacture is used to produce successive layers of a part in a powder bed and offers the ability to produce components closest to their final dimensions, with good surface finish. At this time the process is faster than any other technique of comparable quality, however the parts are not produced at sufficient rate to make them economically viable for any but very h ...
Voir le projet
8
Participants partenaires
TERMINÉ
Development of a new method to produce high efficiency solar concentrators based on polymer casted directly on glass (PolyGlass)
Date du début: 1 déc. 2010, Date de fin: 30 nov. 2012,
To develop a production method for manufacturing of optical lenses with micro structured surface and extreme high precision of details in large format. The Developed Product shall be utilized to improve the efficiency of Solar collectors. The primary target is the Concentrated Photovoltaic (CPV) market. Today the CPV manufacturer use concentrating optics made from PMMA (Acrylic) or silicon on glas ...
Voir le projet
7
Participants partenaires
TERMINÉ
Continuous health monitoring and non-destructive assessment of composites and composite repairs on surface transport applications (ComPair)
Date du début: 1 sept. 2008, Date de fin: 30 nov. 2011,
Composites are used in a wide range of applications in surface transport. Damage to composite components in vehicles and surface transport applications is not always visible to the naked eye and the extent of damage is best determined for structural components by suitable non-destructive and evaluation (NDT & E) techniques. A detailed NDT and/or health monitoring procedure for proper damage assess ...
Voir le projet
12
Participants partenaires
TERMINÉ
Development of a condition monitoring system for tidal stream generator structures (TidalSense)
Date du début: 1 sept. 2009, Date de fin: 31 août 2011,
Due to the increasing demand for renewable energy, a great deal of effort is being put into the development of tidal power generation systems. As these systems go in to commercial production and service, it is important to consider and develop inspection and condition monitoring techniques and systems. Condition monitoring of such systems could be used to greatly reduce the risk of failures and th ...
Voir le projet